CCNP SWITCH 642-813 Official Certification Guide (Part II – Chapter 7 Respuestas correctas test)

1. How is a bridging loop best described?

a. A loop formed between switches for redundancy

b. A loop formed by the Spanning Tree Protocol

c. A loop formed between switches where frames circulate endlessly

d. The round-trip path a frame takes from source to destination

2. Which of these is one of the parameters used to elect a root bridge?

a. Root path cost

b. Path cost

c. Bridge priority

d. BPDU revision number

3. If all switches in a network are left at their default STP values, which one of the following is not true?

a. The root bridge will be the switch with the lowest MAC address.

b. The root bridge will be the switch with the highest MAC address.

c. One or more switches will have a bridge priority of 32,768.

d. A secondary root bridge will be present on the network.

4. Configuration BPDUs are originated by which of the following?

a. All switches in the STP domain

b. Only the root bridge switch

c. Only the switch that detects a topology change

d. Only the secondary root bridge when it takes over

5. Which of these is the single most important design decision to be made in a network running STP?

a. Removing any redundant links

b. Making sure all switches run the same version of IEEE 802.1D

c. Root bridge placement

d. Making sure all switches have redundant links

6. What happens to a port that is neither a root port nor a designated port?

a. It is available for normal use.

b. It can be used for load balancing.

c. It is put into the Blocking state.

d. It is disabled.

7. What is the maximum number of root ports that a Catalyst switch can have?

a. 1

b. 2

c. Unlimited

d. None

8. What mechanism is used to set STP timer values for all switches in a network?

a. Configuring the timers on every switch in the network.

b. Configuring the timers on the root bridge switch.

c. Configuring the timers on both primary and secondary root bridge switches.

d. The timers can’t be adjusted.

9. MAC addresses can be placed into the CAM table, but no data can be sent or received if a switch port is in which of the following STP states?

a. Blocking

b. Forwarding

c. Listening

d. Learning

10. What is the default “hello” time for IEEE 802.1D?

a. 1 second

b. 2 seconds

c. 30 seconds

d. 60 seconds

11. Which of the following is the Spanning Tree Protocol defined in the IEEE 802.1Q standard?

a. PVST

b. CST

c. EST

d. MST

12. If a switch has 10 VLANs defined and active, how many instances of STP will run using PVST+ versus CST?

a. 1 for PVST+, 1 for CST

b. 1 for PVST+, 10 for CST

c. 10 for PVST+, 1 for CST

d. 10 for PVST+, 10 for CST

Saludos a tod@s,

JMHAlegre

Esta entrada fue publicada en CCNP SWITCH 642-813 Official Certification Guide (Part II – Chapter 7 Respuestas correctas Test), CCNP SWITCH 642-813 Official Certification Guide (Part II – Chapter 7 Traditional Spanning Tree Protocol), Cisco, SWITCH 642-813 y etiquetada . Guarda el enlace permanente.

Responder

Introduce tus datos o haz clic en un icono para iniciar sesión:

Logo de WordPress.com

Estás comentando usando tu cuenta de WordPress.com. Cerrar sesión / Cambiar )

Imagen de Twitter

Estás comentando usando tu cuenta de Twitter. Cerrar sesión / Cambiar )

Foto de Facebook

Estás comentando usando tu cuenta de Facebook. Cerrar sesión / Cambiar )

Google+ photo

Estás comentando usando tu cuenta de Google+. Cerrar sesión / Cambiar )

Conectando a %s